ReferenceDesignLibrary

Refine Search

Eval Board Voltage In Topology Current Out Voltage Out (Max) Outputs and Type Efficiency @ Conditions Features Switching Frequency Component Count + Extras Design Author Application / Target Market Main I.C. Base Part
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear All Selections Apply Filters

Designs (150)

150 Results - Page 1/15 |< < 1 2 3 4 5 > >|

EVL6562A-LED: 350mA @ 45V Max, 36 ~ 60V in

Manufacturer: STMicroelectronics

Whenever a lighting application, such as street lighting for example, requires an elevated number of LEDs, there are basically two solutions: the first is to connect all the diodes in series in a single "string"; the second is to place several strings in parallel with fewer elements in each one.

View Design

LM3401-MR16DEMO: 1A @ 6.2V Max, 12VAC, MR16

Manufacturer: Texas Instruments

This design was developed to minimize the current spikes coming out of an electronic transformer to less than 5A, which is a typical transformer rating, when driving an LED MR16 circuit. The off the shelf LED MR16 solutions exhibit spikes that significantly exceed a transformers maximum rated output current which will degrade the reliability of the transformer and reduce its operating lifetime. T…

View Design

LM3464EVAL: 4 Channel @ 350 mA/chan, 12~80V in

Manufacturer: Texas Instruments

This evaluation board demonstrates the high power efficiency and outstanding output current accuracy of the LM3464A typical application circuit. With four LED strings connected, the total output power is about 50W. The schematic, bill of material and PCB layout drawing of the LM3464A evaluation board are provided in this document.

View Design

TPS61150EVM-150: 4 LEDs x 2 @ 15mA, 2.5 ~ 6V in

Manufacturer: Texas Instruments

The Texas Instruments TPS61150EVM-150 evaluation module contains the TPS61150 IC. This EVM provides two independently regulated current outputs using a single inductor step-up (boost) converter.

View Design

STEVAL-ILL010V1: 1 ~ 6 LEDs @ 350 mA, 8 ~ 30V in

Manufacturer: STMicroelectronics

This evaluation board is designed around an L6902D-based DC-DC converter with dimming interface. The board implements both of two well known dimming methods: - Analog current control - Average current control by PWM

View Design

CAT4201AGEVB: 350mA @ 20V Max, 6.5 ~ 28V in

Manufacturer: ON Semiconductor

The CAT4201 is a high efficiency step-down LED driver from Catalyst Semiconductor. This device is designed to drive high brightness LEDs up to 350mA from a power supply up to 28V. The LED brightness is controlled by a single resistor from the RSET pin to GND. Analog dimming and idle mode control are available through the CTRL input. An external circuit is provided on the CAT4201AEVB for PWM dimmin…

View Design

STEVAL-ILL008V1: 1 LED @ 280mA, 0.6 ~ 5.5V in

Manufacturer: STMicroelectronics

The L6920D is used in this flashlight application as it is a high efficiency step-up controller that realizes the conversion from battery voltage to the selected output voltage with only three external components.

View Design

DC1160A: 330mA @ 40V Max, 3 ~ 40V in

Manufacturer: Linear Technology/Analog Devices

Demonstration circuit 1160 is a full-featured LED driver with 2.3A switch current featuring the LT®3518. The board is optimized to drive a 330mA LED string with a total LED voltage between the input voltage and 40V in a boost topology. The high input voltage range, high efficiency low side internal 2.3A NPN power switch, low voltage floating current sense amplifier, soft-start, high side PMOS PWM…

View Design

NCP3065D3SLDGEVB(2): 350mA @ 7 ~ 23V out, 8 ~ 25V in

Manufacturer: ON Semiconductor

* The eval board must be modified for 350mA output. The Transformer/Dual inductor and sense resistor(s). This circuit is intended for driving high power LEDs, such as the Cree XLAMP™ series, Lumileds Luxeon™ Rebel and K2 and OSRAM, Golden and Platinum Dragon™ as well as the OSTAR™.

View Design

STEVAL-ILL007V1: 1 to 3 LEDs @ 0.35, 0.7, or 1A

Manufacturer: STMicroelectronics

The evaluation board is designed to display the full functionality of L5973D as a LED driver to drive one to three 1W, 3W as well as 5W LEDs at 12Vac input. The components selected for the demo board are optimized for 5W LED driver application.

View Design
150 Results - Page 1/15 |< < 1 2 3 4 5 > >|