ReferenceDesignLibrary

Refine Search

Eval Board Amplifier Type Number of Outputs Output Power (RMS) @ Load Voltage In THD+N (1kHz) @ Conditions Features Efficiency @ Conditions Component Count + Extras Design Author Application / Target Market Standby Current [Typical] Quiescent Current [Typical] Main I.C. Base Part
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear All Selections Apply Filters

Designs (98)

98 Results - Page 1/10 |< < 1 2 3 4 5 > >|

SSM2305-EVALZ: 2.8 W @ 4 Ω, 2.7 ~ 5.5 V

Manufacturer: Analog Devices Inc.

The SSM2305 is a fully integrated, single-chip, mono Class-D audio amplifier that is designed to maximize performance for mobile phone applications. The application circuit operates from a single 2.5 V to 5.5 V supply and is capable of delivering 2.8 W of continuous output power with less than 10% THD + N driving a 4 Ω load from a single 5.0 V supply.

View Design

TPA3007D1EVM: Mono 6.5 Watt @ 8 Ω, Class D Amp

Manufacturer: Texas Instruments

The TPA3007D1 is a 6.5-W mono bridge-tied load (BTL) class-D audio power amplifier with high efficiency, eliminating the need for heat sinks. The TPA3007D1 can drive 8Ω speakers with only a ferrite bead filter required to reduce EMI.

View Design

LM3886: #2) PA100 - 100W Parallel AB Amp

Manufacturer: Texas Instruments

The parallel amplifier is another configuration that can be used to obtain higher output power levels by combining two IC outputs and doubling output current drive capability. The parallel topology provides a great way of achieving higher power levels while keeping within IC power dissipation limits by driving low impedance loads, which is the case for many self-powered speaker and powered subwoo…

View Design

STEVAL-CCA002V1: 1W @ 8Ω, 2.5 ~ 5.5V in

Manufacturer: STMicroelectronics

This evaluation board is designed with the TS4994 low power differential audio amplifier. The micro-package DFN10 (dual flat non-leaded 10 pins) allows space saving and good thermal dissipation. The differential gain is set at 1 V/V and can be adapted as necessary through a modification of the R1 to R4 values.

View Design

LM4667MMBD: 1.3W @ 8Ω, 2.7 ~ 5V, Class D

Manufacturer: Texas Instruments

The LM4667 is a fully integrated 1.3W, single-supply high efficiency (Class D) switching audio amplifier. It features an innovative modulator that eliminates the LC output filter used with typical switching amplifiers.

View Design

TPA3110D2EVM: 15W x 2 @ 8 Ohm, 8 ~ 26V in

Manufacturer: Texas Instruments

The TPA3110D2 evaluation module consists of a single 15-W, Class-D, stereo audio power amplifier complete with a small number of external components mounted on a circuit board that can be used to directly drive a speaker with an external analog audio source as the input. The EVM’s default output filter configuration supports filter-free operation, but can easily be configured to support LC filter…

View Design

STEVAL-CCA029V1: 5W x 2 @ 8Ω, 5 ~ 14V in, Class D

Manufacturer: STMicroelectronics

The STEVAL-CCA029V1 is a demonstration board designed for the TDA7491LP dual BTL class-D audio amplifier. This application note provides the board specifications and a quick-start list for stand-alone operation. Also included are the schematic, printed circuit board layout and bill of material.

View Design

EVAL-SSM3302Z: 8W x2 @ 8Ω, 7 ~ 18V in, Class D

Manufacturer: Analog Devices Inc.

The SSM3302 is a fully integrated, high efficiency, stereo Class-D audio amplifier. The application circuit requires a minimum of external components and operates from a single 7 V to 18 V supply. It is capable of delivering 2 × 8 W of continuous output power into an 8 Ω load (or 2 × 10 W into 4 Ω) with <1% total harmonic distortion plus noise (THD + N) from a 12 V supply. In addition, while m…

View Design

LM48511SQBD: 6.7W @ 4Ω, 3 ~ 5.5V in

Manufacturer: Texas Instruments

The LM48511 integrates a boost converter with a high efficiency Class D audio power amplifier to provide 3W continuous power into an 8Ω speaker when operating from a 5V power supply. When operating from a 3V to 4V power supply, the LM48511 can be configured to drive 1 to 2.5W into an 8Ω load with less than 1% distortion (THD+N).

View Design

STEVAL-CCA016V1: Stereo 2.8W @ 4Ω, Class D

Manufacturer: STMicroelectronics

This demonstration board is designed to evaluate the performances of TS4999, that is a stereo fully differential Class-D power amplifier. It can drive up to 1.35 W into a 8 Ω load at 5 V per channel.

View Design
98 Results - Page 1/10 |< < 1 2 3 4 5 > >|